Added safety with front heat guard: This heater has an additional 5mm thick panel on the front, 25mm away from the panel creating the heat. This results in extra “touch safety” for babies, toddlers and elderly who don’t have a quick reflex reaction time when touching something hot.
Efficient heat distribution: This heater design will efficiently distribute the generated heat throughout the room using natural convection. The 25mm gaps between the heater panel itself and the foil lined wall as well as between the heater panel and the heat guard provide perfect sized channels for air to be heated and natural convection to occur. There is still a small amount of radiant heat, so all our heaters need a clear space in front of them, but you can have items close either side of them.
Economical heat technology: Amaze convection wall hung panel heaters can be used for long periods of time and have a low running cost. This can also help to lower the home heating costs up to 50% compared to other forms of space heaters. And warm just the room of your choice without having to heat the entire house!
Running costs: The beauty of our fixed wattage heaters is you know how much power you will use before you turn them on. This midi wall hung panel heater only uses 1 unit of electricity every 2½ hours. Depending on where you live, that could be less than 8 cents per hour on night rate, and around 10 cents per hour on peak rate. If you think 400 watts is going to get your room too hot, you can add a plug-in thermostat.
Room size: As a general guideline, this 400W heater is usually suitable for keeping the chill off in bedrooms, offices and living spaces around 12 sqm, although some people report that it does the job for them in a well-insulated room of up to 16 sqm. Appropriate room size for any of the Amaze panel heaters can depend on many things including climate, outdoor temperature, insulation, double glazing, age of building, temperature of adjacent rooms and even a person’s concept of warmth. All Amaze heaters can be used with a plug-in time switch or plug-in thermostat.
Paintable: This heater can be painted with any water-based (acrylic) non-enamel paint.
Unobtrusive: The heating panel itself (the panel with the heating element inside) is only about 12mm thick, and the heat guard panel is about 5mm thick. The heating panel sits 25mm off the wall. There is another 25mm gap between the heating panel and the front heat guard panel. So the total thickness out from the wall is less than 70mm. The heater must be a minimum of 150mm above the floor.
Quiet: No fan! Less noise! This can make it better for asthma and allergy sufferers with less dust being pushed around. And obviously perfect for sleeping.
Composition: What’s the heater made of? The heating panel of this Amaze heater is made with two sheets of durable non-conducting superior calcium silicate boards specially made for us. The glue that bonds both sheets has insulating properties with excellent dielectric strength. All components are certified materials and fire retardant. The resulting complete panels have extra reinforced strength (making them shatter proof amongst other things) and are triple insulated (excellent for safety). The front heat guard is made with a sheet of the same material.
Conforms to NZ standards: All Amaze heaters sold in New Zealand comply with NZ standards, and we can present a Supplier’s Declaration of Conformity.
Easy to install: Screw to the wall using supplied mounting kit, foil heat reflector and template. Plug it in with the approx. 1.7m long cord and plug. An extension cord or multibox can be safely used, as the wattage of the heater is so low. A plug-in timeswitch (or timer) and/or plug-in thermostat can also be safely used.
Installation instructions are included with heater, and briefly are:
- Mark all 4 position holes on the wall, using template supplied.
- Drill the pilot holes for the drywall anchors.
- Screw the drywall anchor into each pilot hole.
- Pin the foil sheet to the wall using supplied pins.
- Secure the four mounting legs to the wall using the supplied screws.
- Align the holes on the heater panel with the mounting legs.
- Firmly screw in the four legs.
- Finalize the position of the heater on the wall while tightening the screws.
- Tighten the cap/nuts over the four mounting posts to lock the unit in place.
Please note that all accompanying images on this website are for illustrative purposes only. If there is any discrepancy between the information in the images and the words written here, then the actual text on our website prevails.
Reviews
There are no reviews yet.